Share this page

PEAK 8920VL2

Intel® Dual-Core Xeon® LGA771 Processor with Fully Buffered DIMM/
2 x PCI Express Gigabit LAN/6 x USB
  • Main Feature
  • Quad Core/Dual-Core Xeon® Processor SBC
  • Intel® 5000P Embedded Chipset with Longevity Support
  • Robust Mechanism Design for Enhanced Product Reliability
  • Up to 8GB ECC/Register FB-DIMM DDR 2 Memory
  • Dual PCI Express Gigabit Ethernet for High Networking Bandwidth
  • Four USB 2.0 Directly Output from Bracket to Save the Cabling Cost
  • Flexible Design for Single/Dual Processors
  • Dedicated CPU Cooler Design for Thermal Solution
Add to Inquiry
Datasheet(PDF)
CPU Support Support Dual-Core Intel® Xeon® processor 5100 series and Quad-Core; Intel® Xeon® Processor 5300 series (80W) Intel® Embedded Processor List ( Intel® Longevity CPU): Dual-Core Intel® Xeon® Processor (5130 & 5140); Dual-Core Intel® Xeon® Processor LV (5128, 5138, 5148) 1066/1333 MHz FSB support
Main Memory 4 x 240-pin four channel DDR 2 FB-DIMM Support ECC/Register DDR2 memory up to 8GB
Chipset Intel® 5000P memory controller Hub Intel® 6321ESB I/O controller Hub
BIOS AMI BIOS Plug & Play support Support Soft off, Wake on LAN, Power On by PS2 Keyboard Function Key, RTC alarm Power On Power on after power failure 8M-bit flash ROM
On-board LAN 2 x Intel® 82573L PCI Express Gigabit Ethernet Support Boot From LAN (PXE) Support Wake On LAN
Display ATI ES1000 PCI graphic Controller 32MB DDR2 SDRAM VGA Memory 1 x DB15 VGA port
I/O Interface USB 2.0: 4 ports through I/O bracket USB 2.0: 2 ports, with 1x6 JST (2.5mm ) Serial port: 2 ports, with 2x5 box-header (2.0mm) support RS-232 only Parallel port: 1 port , with 2x13 box-header (2.0mm), Bi-directional, EPP/ECP PS/2: 1 x Mini-Din Keyboard/Mouse GPIO: Support 4 sets of general purpose I/O each with TTL level (5V) interface FAN: 2 x 4-pin FAN connectors (for CPU coolers) 1 x on board buzzer 1 x 2-pin power on switch/1 x SMBus 2.0 to Backplane 1 x 2-pin header for reset/1 x 5-pin header for key lock 1 x 2-pin header for power LED/1 x 2-pin header for HDD LED
Watchdog Timer Watchdog Timer is programmable by software from 0 to 255 seconds (Tolerance 10% under room temperature 25°C)
Storage SATA: 2 ports, support RAID 0,1 through Backplane IDE: 1 x 40-pin IDE connector, support Ultra ATA 33/66/100 1 x 2-pin JST (2.5mm) power connector for DOM (Disk On Module)
System Monitor 8 voltage (For +3.3V, +12V, Vcore x2, 1.8V, 1.5V, 5Vsb) 3 temperature (For 2 CPU and system) 3 FAN speed monitor ( 2 for CPU and 1 for ESB2)
On-board RTC On-chip RTC with battery back up 1 x External Li-Lon battery
Dimensions PICMG 1.3 SHB; 338.58mm (L) x 126.39mm (W) (13.3" x 4.9")
Power Input Power source from backplane through PICMG 1.3 Golden Finger, support ATX mode-- CPU:2 x Dual-Core Xeon 3.0G, Memory:4 x FBD DDR2 2.0GB:+12V +5V +3.3V +5Vsb; Full-Loading Mode:21.4A 2.07A 3.85A 0.04A; Light-Loading Mode:10.59A 1.69A 3.63A 0.04A. (NOTE: 1.Full Loading: Utilize CPU 100% with Burn-in test running 2.Light Loading: Utilize CPU loading below 5% without data or application running)
Environment Operating Temperature: 0°C to 60°C (for Board Level Only) Storage Temperature: -20°C to 85°C Relative Humidity: Operating: 10% to 90% (non-condensing); Non-Operating: 5% to 95% (non-condensing)
Certifications CE approval FCC Class A
Add to Inquiry
Take a minute and tell us what you think!